Sierra Victor Industries MODEL 10-95 - 10' x 95 Ton BETENBENDER® Hydraulic Press Brake

10' x 95 Ton BETENBENDER® Hydraulic Press Brake
[10-95]

Call For Price

10' x 95 Ton BETENBENDER® Hydraulic Press Brake

Click to enlarge



ITEM	10' x 95 Ton Hydraulic Press Brake
MAKE	BETENBENDER®
MODEL	10-95
PART	10-95
PRICE	$CALL
CLICK HERE FOR FREIGHT QUOTE AND AVAILABILITY

PHOTOS - PLEASE CLICK ON THUMBNAIL BELOW TO VIEW PHOTOS

WARRANTY

1 YEAR

SPECIFICATIONS

Maximum Tonnage		95 Tons
Maximum Bending Length		120"
Maximum Stroke Length		8"
Open Height		14"
Throat Depth		8"
Distance Between Housings		78-1/2"
Ram Repeatability		+/- .002"
Ram Speed:	Approach (Rapid)	114 IPM
	Bending	50 IPM
	Return	168 IPM
Hydraulic Pressure		2,500 lbs.
Hydraulic Oil Capacity		51 gallons
Machine Weight		20,100 lbs.
Motor Horsepower		20
Machine Dimensions:	Overall Height	98.5"
	Overall Length	135"
	Overall Width	56.5"
OUR PRICE		$CALL

Specifications are subject to change without notice.

NOTE: Data is provided by the manufacturer.

FEATURES

ACCURACY: Every Betenbender machine is thoroughly inspected and tested.
1.Parallelism is maintained between bed and ram or at preset angle by using precision automatic leveling controls. Parallelism is maintained at +/-.002" in low speed.
2.The ram bottom reversal point is controlled by precise limit switches referenced off the bed. This isolates housing deflections, which can interfere with its accuracy.
ENHANCED PRODUCTIVITY: Return speeds and rapid advance facilitates high cycle rates. Operator control is simplified by slow and press speed, thus work spoilage is avoided. Rapid advance with automatic change. The point of speed change is fully adjustable by electric limit switch. Micrometer type tilt adjustment is graduated in .001" increments permitting ram tilt adjustments up to 1/2" in either direction.
ELECTRO MECHANICAL STROKE CONTROL is bed referenced. Bottom limit is manually set with a lead screw and displayed by an mechanical readout calibrated in .001" increments.
VERSATILITY: BETENBENDER'S press brakes have long full tonnage strokes, adjustable length and selectable speed combinations, adjustable height for short stroke, 2-speed standard and the optional 3- speed for adjustable low speed to
prevent whip.
ELECRICAL EQUIPMENT: Meets requirements of NFPA no.79, JIC and construction requirements of the latest ANSI B-11.3 Standards. Includes drip-proof , continuous
duty 45 degree Celsius ambient hydraulic pump motor wired for 230 or 460 volt, 3 phase 60 hertz.
DEPENDABILITY: Self-lubricating replaceable non-metallic ways prevent galling and provide long service life. Cylinders are high-strength, all steel. To minimize wear and provide a superior oil seal, inside cylinder surfaces are honed to a mirror finish. Compact, precision machined aluminum manifold incorporates off-the shelf components, minimizes piping and consolidates "O" ring mounted valves. Quiet, vane type, constant volume pumps. In keeping with good hydraulic design practice, these energy efficient pumps are located outside the reservoir. Filtration of contaminants as small as 10 microns is accomplished with intake and discharge filters. A built-in magnetic trap and air breather filter provides added protection against contaminants. Reservoir of large capacity facilitates effective heat dissipation. A fluid level gauge
is provided.
CONTROL: Main Control Cabinet - NEMA 12 enclosures mounted in the right housing
containing: magnetic non-reversing motor starter and 120 volt circuit. Main motor START button and STOP button are illuminated. RAM UP and RAM DOWN buttons. RUN/JOG Switch. Fusible disconnect.
CYLINDERS - Chromed rod for increased wearing surface. Cast Iron Piston with
Polished Cylinder Wall Provides Greater Durability and Less Wear. double buttress
thread on piston cap and rod gives increased pressure resistance.
MAINTENANCE: Clevis mounted cylinders eliminate cylinder binding by reducing the possibility of oil leaks from cylinder binding. (Pins & bushings do not rotate under load, this reduces excessive wear)
PLEASE SPECIFY VOLTAGE
TOOLING: Available Upon Request
*Does Not Include Tooling or Die Block Unless Otherwise Quoted
***We Recommend Using 85° or 88° tooling for Air Bending
Made in USA

STANDARD EQUIPMENT

Clamp Type Back-gauge-Manual - Adjustable X,Y,Z
NEMA Electrics
All Hydraulic Fluid Included
American Made Motor
Hour Meter
Bottom Time Delay
Three Position Foot Pedal
Depth Stop w/Digital Readout
All Steel Construction
Disconnect Switch
Three Speed (95T and Larger)

OPTIONAL ITEMS

CNC 2- Axis Backgauge: Automec CNC 150 Programmable Backgauge (2-Axis): System includes 2-axis(X-backgauge & Y-ram) dual drive, 7’ titling gauge bar system, controller and display, pendent mount, hardware, (1) set interconnecting cables, auto ram switch, instruction manual and 24 month warranty, mounted, set-up and training -For more information CLICK HERE
Manual Front Reading Backgauge (24") w/Mechanical Readout*
Power Front Reading Backgauge w/5 Station NC "Go To" Controller on Pendant
Power Ram Adjustment w/5 Station NC "Go To" Controller on Pendant
Extra Length on Backgauge
Micrometer Precision Gauge Unit (2 Required)
CNC Ram Stop
CNC Backgauge
24" Support Arms "Slide" Type*
Extend Support Arms (each)
Disappearing Stops
Work Light*
Variable Tonnage Control*
One Shot Lubrication*
Automatic Lubrication
Oil Cooler
Light Curtain w/Full Fence*
Operator Station Palm Control*
Additional Foot Pedal w/Key Lock
Palm Buttons/Foot Control System
(Hand buttons to preset height, stop and hold, foot to continue to shut height.)
Dove Tails or T-Slots
Ram Machining
Bed Machining Angle Brackets
Angle Brackets (Plates) for Top (4"x4") 18" Shorter than Bed
Angle Brackets (Plates) for Bottom (4"x4") 18" Shorter than Bed
Increase Throat Gap or Increase Open Height
Increase Stroke Length
Keylock Switch
Die Rollover Bars (Recommended for 4/Way Dies)
Air Lift (Recommended for 4/Way Dies)
Dual Calibration
208V
Crating Charge (Not An Export Crate) Still Requires Tarping
Special Paint Colors
Bolt/Shim Kit for Leveling
*RECOMMENDED OPTIONS
**ASK ABOUT OPTIONS NOT LISTED.

Sierra Victor ... your source for new and used machinery.