Sierra Victor Industries MODEL 12-190 - 12' x 190 Ton BETENBENDER® Hydraulic Press Brakes

12' x 190 Ton BETENBENDER® Hydraulic Press Brakes
[12-190]

Call For Price

12' x 190 Ton BETENBENDER® Hydraulic Press Brakes

Click to enlarge



ITEM	12' x 190 Ton Hydraulic Press Brake
MAKE	BETENBENDER®
MODEL	12-190 ( FOR MORE BRAKES - CLICK HERE )
PART	12-190
PRICE	$CALL
CLICK HERE FOR FREIGHT QUOTE AND AVAILABILITY

PHOTOS - PLEASE CLICK ON THUMBNAIL BELOW TO VIEW PHOTOS

WARRANTY

1 YEAR

SPECIFICATIONS

Maximum Tonnage		190 Tons
Maximum Bending Length		144"
Maximum Stroke Length		8"
Open Height		14"
Throat Depth		8"
Distance Between Housings		126-1/2"
Ram Repeatability		+/- .002"
Ram Speed:	Approach (Rapid)	55 IPM
	Bending	25 IPM
	Return	66 IPM
Hydraulic Pressure		2,500 lbs.
Hydraulic Oil Capacity		80 gallons
Motor Horsepower		20
Machine Weight		25,000 lbs.
Machine Dimensions:	Overall Height	103"
	Overall Length	159"
	Overall Width	56.5"
OUR PRICE		$CALL

Specifications are subject to change without notice.

NOTE: Data is provided by the manufacturer.

FEATURES

ACCURACY: Every Betenbender machine is thoroughly inspected and tested.
1.Parallelism is maintained between bed and ram or at preset angle by using precision automatic leveling controls. Parallelism is maintained at +/-.002" in low speed.
2.The ram bottom reversal point is controlled by precise limit switches referenced off the bed. This isolates housing deflections, which can interfere with its accuracy.
ENHANCED PRODUCTIVITY: Return speed and rapid advance facilitates high cycle rates. Operator control is simplified by slow and press speed, thus work spoilage is avoided. Rapid advance with automatic change. The point of speed change is fully adjustable by electric limit switch. Micrometer type tilt adjustment is graduated in .001" increments permitting ram tilt adjustments up to 1/2" in either direction.
ELECTRO MECHANICAL STROKE CONTROL: is bed referenced. Bottom limit is manually set with a lead screw and displayed by an mechanical readout calibrated in .001" increments.
VERSATILITY: BETENBENDER'S press brakes have long full tonnage strokes, adjustable length and selectable speed combinations, adjustable height for short stroke, 2-speed standard and the optional 3- speed for adjustable low speed to
prevent whip.
ELECRICAL EQUIPMENT: Meets requirements of NFPA no.79, JIC and construction requirements of the latest ANSI B-11.3 Standards. Includes drip-proof, continuous duty 45 degree Celsius ambient hydraulic pump motor wired for 230 or 460 volt, 3 phase
60 hertz.
DEPENDABILITY: Self-lubricating replaceable non-metallic ways prevent galling and provide long service life. Cylinders are high-strength, all steel. To minimize wear and provide a superior oil seal, inside cylinder surfaces are honed to a mirror finish. Compact, precision machined aluminum manifold incorporates off-the shelf components, minimizes piping and consolidates "O" ring mounted valves. Quiet, vane type, constant volume pumps. In keeping with good hydraulic design practice, these energy efficient pumps are located outside the reservoir. Filtration of contaminants as small as 10 microns is accomplished with intake and discharge filters. A built-in magnetic trap and air breather filter provides added protection against contaminants. Reservoir of large capacity facilitates effective heat dissipation. A fluid level gauge is provided.
CONTROL: Main Control Cabinet - NEMA 12 enclosures mounted in the right housing containing: magnetic non-reversing motor starter and 120 volt circuit.
Main motor START button and STOP button are illuminated.
RAM UP and RAM DOWN buttons.
RUN/JOG Switch.
Fusible disconnect.
MAINTENANCE: Clevis mounted cylinders eliminate cylinder binding by reducing the possibility of oil leaks from cylinder binding. (Pins & bushings do not rotate under load, this reduces excessive wear)
*PLEASE DESIGNATE VOLTAGE REQUIRED
Made in USA

STANDARD EQUIPMENT

Clamp Type Back-gauge-Manual
Adjustable X,Y,Z
Bottom Time Delay
Three Position Foot Pedal
NEMA Electrics
Depth Stop w/Digital Readout
All Hydraulic Fluid Included
All Steel Construction
American Made Motor
Disconnect Switch
Hour Meter
Two-Speed Ram

OPTIONAL ITEMS

Automec CNC 150HD Programmable Backgauge: System includes dual drive, 11’ titling gauge bar system, controller and display, pendent mount, hardware, (1) set interconnecting cables, auto ram switch, instruction manual and 24 month warranty, mounted, set-up and training - 1st Axis-Backgauge. 2nd Axis-Ram Control.
*Tooling Available Upon Request

Sierra Victor ... your source for new and used machinery.